Effect of Al2O3 Particles and Precipitation Hardening on the Properties of Cast 332 Aluminum Alloy

Main Article Content

Akeel Dhahir Subhi Hussein Najim Abdullah


In this work, 332 Al alloy was prepared and reinforced with (0.5% and 1%) nano-Al2O3 particles. The prepared unreinforced and reinforced 332 Al alloy with nano-Al2O3 were solution heat treated (T6) at 510 ̊C and aged at 225 ̊C with different times (1, 3, and 5 h). Hardness test was performed on all the prepared alloys. All prepared alloys were dry slided under different applied loads (5, 10, 15, and 20 N) against steel counterface surface using pin on disk apparatus. The results showed that refinement effect was observed after addition of nano-Al2O3 particles and a change in silicon morphology after performing the solution heat treatment. The results also showed that hardness was increased and the wear rate was decreased with increasing the nano-Al2O3 particles in the matrix of 332 Al-Alloy

Article Details

How to Cite
SUBHI, Akeel Dhahir; ABDULLAH, Hussein Najim. Effect of Al2O3 Particles and Precipitation Hardening on the Properties of Cast 332 Aluminum Alloy. Al-Khwarizmi Engineering Journal, [S.l.], v. 14, n. 4, p. 125- 132, dec. 2018. ISSN 2312-0789. Available at: <http://alkej.com/index.php/en/article/view/748>. Date accessed: 23 mar. 2019. doi: https://doi.org/10.22153/kej.2018.05.007.


[1] J.R. Davis, ASM Specially Handbook: "Aluminum and Aluminum Alloys", ASM International Materials Park, Ohio, (1993).
[2] ASM Handbook, Vol. 2 " Properties and Selection: Nonferrous Alloys and Special-Purpose Materials." Materials Park, Ohio (1990).
[3] E.R. Wang, X.D. Hui, G.L. Chen. "Eutectic Al–Si–Cu–Fe–Mn alloys with enhanced mechanical properties at room and elevated temperature." Materials & Design 32, (2011): 4333-4340.
[4] M.C Shankar, P.K Jayashree, R. Shettya, A. Kinia and S.S Sharma. "Individual and combined effect of reinforcements on stir cast aluminium metal matrix composites-a review." International Journal of Current Engineering and Technology 3, no. 3 (2013): 922-934.
[5] A. Necat, and A. Coban. "The tensile behavior and microstructure of Al2O3/SiCp reinforced aluminum-based MMCs produced by stir casting method." International Journal of Science and Advanced Technology 2, no. 5 (2012): 78-86p.
[6] Krishnan, B. P., N. Raman, K. Narayanaswamy, and P. K. Rohatgi. "Performance of an Al-Si-graphite particle composite piston in a diesel engine." Wear 60, no. 1 (1980): 205-215.
[7] S. Shivkumar, S. Ricci, C. Keller, and D. Apelian. "Effect of solution treatment parameters on tensile properties of cast aluminum alloys." Journal of Heat Treating 8, no. 1 (1990): 63-70.
[8] M. Kok, "Production and mechanical properties of Al 2 O 3 particle-reinforced 2024 aluminium alloy composites." Journal of Materials Processing Technology 161, no. 3 (2005): 381-387.
[9] M. Kök, and K. Özdin. "Wear resistance of aluminium alloy and its composites reinforced by Al2O3 particles." Journal of Materials Processing Technology 183, no. 2 (2007): 301-309.
[10] Z. Fizam, K. R. Ahmad, and R. Daud. "Effect of Heat Treatment on Microstructure, Hardness and Wear of Aluminum Alloy 332." In Applied Mechanics and Materials, vol. 786, pp. 18-22. Trans Tech Publications, 2015.
[11] Salleh, M. S., M. Z. Omar, J. Syarif, and M. N. Mohammed. "Thermodynamic calculations of aluminium alloys for semi-solid processing." In 7th International Conference on Mathematics, Simulation, Modelling, Cambridge, MA, United States. 2013.
[12] S. Yu, P. Shao-ping, L. Xue-ran, Y. Zi-run, S. Guo-xiong "Nucleation and growth of eutectic cell in hypoeutectic Al− Si alloy-TNMSC." The Chinese Journal of Nonferrous Metals 21, (2011): 2186-2191.