Main Article Content
In this research, (MOORA) approach based– Taguchi design was used to convert the multi-performance problem into a single-performance problem for nine experiments which built (Taguchi (L9) orthogonal array) for carburization operation. The main variables that had a great effect on carburizing operation are carburization temperature (oC), carburization time (hrs.) and tempering temperature (oC). This study was also focused on calculating the amount of carbon penetration, the value of hardness and optimal values obtained during the optimization by Taguchi approach and MOORA method for multiple parameters. In this study, the carburization process was done in temperature between (850 to 950 ᵒC) for 2 to 6 hours. Quenching was done for the specimens after heat treatments in furnace chamber by using different quench solutions, water, salt and polyvinyl alcohol. Analysis of variances - (ANOVA) were performed for nine experiments in order to optimize the problem that was associated with multiple criteria (parameter) to achieve maximum hardness and depth penetration. The program results showed that the optimum conditions are carburization temperature (950 oC), carburization time (2 hrs.), tempering temperature (200oC), tempering time (10 hrs.), and activator (10 wt. %). Furthermore, the best quenching media was the polyvinyl alcohol.
Copyright: Open Access authors retain the copyrights of their papers, and all open access articles are distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution and reproduction in any medium, provided that the original work is properly cited. The use of general descriptive names, trade names, trademarks, and so forth in this publication, even if not specifically identified, does not imply that these names are not protected by the relevant laws and regulations. While the advice and information in this journal are believed to be true and accurate on the date of its going to press, neither the authors, the editors, nor the publisher can accept any legal responsibility for any errors or omissions that may be made. The publisher makes no warranty, express or implied, with respect to the material contained herein.
 D. Gandy, "Carbon Steel ", Handbook, Electric Power Research Institute, pp: (2-4), March, 2007.
 A. Clark, "Comparison of tempering and quench and tempering processes for carburized automotive steels", M.Sc. Thesis Submitted to University of Windsor, 2013.
 A. J. Patel, S. N. Chaudhari, “Effect of different tempering temperatures and different load on wear behavior and mechanical properties on mild steel”, International Journal of Advance Engineering and Research Development, Vol. 2, Issue 10, pp: (69-76), October, 2015.
 William D. Callister, “Materials science and Engineering”, University of Utah, Salt Lake City pp: (325-326), 2007. 
 C. M. Méndez, M. M. Covinich, A. E. Ares, "Resistance to corrosion and passivity of 316L stainless steel directionally solidified samples", In Tech., CC BY 3.0 License, Book edited by M. Aliofkhazraei, ISBN: 978-953-51-1223, http:// dx.doi.org/10.5772/57275, (2014).
 O.S. Fatoba1, O. l. Akanji, A. S. Aasa, "Optimization of carburized UNS G10170 steel process parameters using (Taguchi) approach and response surface model (RSM)", Journal of Minerals and Materials Characterization and Engineering, Vol. 2, pp: (566-578), 2014.
 J. Gupta, “Mechanical and wear properties of carburized mild steel samples”, Mechanical Engineering, M.Sc. thesis submitted to the National Institute of Technology, Rourkela, May, 2009.
 E. Santuliana, “Effect of surface treatments on mechanical properties of low alloy sintered steels”, Ph.D. Thesis Submitted to University of Trenno -Italy, April, 2011.
 A. K. Hussein, L.K. Abbas, J. J. Dawood and N.J. Ismae, “Modeling of Carburization Parameters Process for Low Carbon Steel”, Eng. & Tech. Journal, Vol. 34, Part (A), No. 6, pp: (1069-1079), 2016.
 Bulan Abdullah, S.K. Aliasa, Ahmed Jaffara, Syazuan Abdul Latipa, Salmiah Kasolanga, Mohd Faizul Izhama, Muhd Azimin Abd Ghania, “Mechanical properties of paste carburized ASTM A516 steel”, The Malaysian International Tribology Conference, MITC, pp: (525-530), 2013.
 S. A. Barabasi, A. Florescu, “Optimization of deep carburizing heat treatment”, International Journal of Information Technology and Business Management, Vol.32, No.1, pp: (23-28), December, 2014.
 J. Petrik, “The microhardness of heat treated carbon steel, department of integrated management”, Metallurgical Faculty, Materials science (MEDŽIAGOTYRA). Vol. 20, No. 1, pp: (21-24), 2014.
 K. Palaniradja, N. Alagumurthi, V. Soundararjan, “Optimization of Process Variables in Gas Carburizing Process: A Taguchi Study with Experimental Investigation on SAE 8620 and AISI 3310 Steels”, Pondicherry Engineering College, Vol. 29, pp: (279-284), 2005.
 R. Singh, "Investigation of Optimal Process Parameters for Mechanical and Wear Properties of Carburized Mild Steel using Taguchi Approach”, Int. J. Eng. Sci. Adv. Research, Vol. 1, No. 1, pp: (90-92), March, 2015.
 M. A. Birnfeld, G. Pintaúde, J. C. K. das Neves, “Effect of carburized steel hardness on surface roughness and residual stresses after manufacturing operations”, International Congress of Mechanical Engineering, Vol. 20, pp: (57-64), Gramado, RS, Brazil ,15-November-2009.
 V.B. Cassapi, “Application of rock hardness and abrasive indexing to rock excavating equipment selection”. PhD thesis, Submitted to University of Nottingham, (1987).
 K. Genel, M. Demirkol, “Effect of case depth on fatigue performance of AISI 8620 carburized steel”, International Journal of Fatigue, Vol. 21, pp: (207–212), 1999.
 W. Karel, M. Brauers, E. K. Zavadskas, “The MOORA method and its application to privatization in a transition economy”, Control and Cybernetics, Vol. 35, No. 2, pp: (207-212), 2006.
 H. Singh, “Taguchi Optimization of Process Parameters: A review and case study”, International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974, Vol. 1, issue 11, April-June, pp: (39-41), 2012.
 F. George. V. Voort, F. Gabriel, M. Lucas, “Microstructural Characterization of Carburized Steels”, Heat Treating Progress, 4 Edt September, 2009.